Difference between revisions of "How to modify vehicle speeds"

From Bergsbruk
Jump to navigation Jump to search
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:


==Hydraulic Speed==
==Hydraulic Speed (Bergsbruk V2)==
[[File:BergsbrukVehicleSpeed.png|thumb|1229x1229px]]
[[File:BergsbrukVehicleSpeed.png|thumb|1229x1229px]]


When your inside a vehicle Press E to open the ECCS, Press the SPEED tab, Here you can edit all hydraulic speeds for that machine, it will not carry over to other machines.  
When your inside a vehicle '''Press E''' to open the ECCS, Press the '''SPEED''' tab, Here you can edit all hydraulic speeds for that machine, it will not carry over to other machines.  


WM1/WM2 is the 2 Work Modes you have on machines like the excavator when one controls the tracks and one the arm  
'''WM1/WM2''' is the 2 Work Modes you have on machines like the excavator when one controls the tracks and one the arm  


The info "(Swing)" will not be accurate for most or any machines but have them so its not just numbers to remember what axis to adjust   
The info "(Swing)" will not be accurate for most or any machines but have them so its not just numbers to remember what axis to adjust   


Axis 1 & Axis 7 = W & S   
'''Axis 1 & Axis 7''' = W & S   


Axis 2 & Axis 8 = A & D  
'''Axis 2 & Axis 8''' = A & D  


Axis 3 & Axis 9 = L-Shift & L-Ctrl   
'''Axis 3 & Axis 9''' = L-Shift & L-Ctrl   


Axis 4 & Axis 10 = Up Arrow & Down Arrow  
'''Axis 4 & Axis 10''' = Up Arrow & Down Arrow  


Axis 5 & Axis 11 = Left Arrow & Right Arrow  
'''Axis 5 & Axis 11''' = Left Arrow & Right Arrow  


Axis 6 & Axis 12 = R-Shift & R-Ctrl <br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br /><br />
'''Axis 6 & Axis 12''' = R-Shift & R-Ctrl <br /><br /><br /><br /><br />




<br /><br /><br />
==Hydraulic Speed (Bergsbruk V3)==
[[File:HydraulicSpeed.png|thumb|1229x1229px]]
When your inside a vehicle '''Press I''' to open the ECCS, Press the '''SPEED''' tab, Here you can edit all hydraulic speeds for that machine, it will not carry over to other machines.


'''Primary/Secondary''' is the 2 Work Modes you have on machines like the excavator when one controls the tracks and one the arm 


'''Axis 1'''  = W & S 


'''Axis 2'''  = A & D


'''Axis 3'''  = L-Shift & L-Ctrl 


'''Axis 4'''  = Up Arrow & Down Arrow


'''Axis 5'''  = Left Arrow & Right Arrow


'''Axis 6'''  = R-Shift & R-Ctrl <br /><br />'''Steering Speed''' is for wheeled vehicles


<br /><br /><br /><br /><br /><br /><br />




==Drivetrain Speed (Bergsbruk v2) ==
[[File:BergsbrukVehicleDrivetrain.png|thumb|1229x1229px]]
When your inside a vehicle '''Press E''' to open the ECCS, Press the '''CTRL''' tab, and press '''DEV DRIVETRAIN''' Here you can edit all drivetrain speeds for that machine, it will not carry over to other machines.
Here you can edit how each gear behaves, Also set the '''Max RPM''', '''Idle RPM''', and the '''Max gear''' is the amount of gears the vehicle has, '''REMEMBER to save changes!'''
'''End Speed:''' The top speed the vehicle will have at that gear
'''Starts Speed:''' The minimum speed, dont touch this
'''Up Shift:''' The speed it will automaticly shift up, if its a automatic transmission
'''Down Shift:''' The speed it will automaticly shift down, if its a automatic transmission
'''High RPM''': Highest RPM the engine will go to on that gear
'''Low RPM''': Lowest RPM the engine will go to on that gear
'''Max Torque:''' The max amout of torque the engine has at the High RPM
'''Min Torque''': The max amout of torque the engine has at theLow RPM








== Drivetrain Speed ==
# [[File:BergsbrukVehicleDrivetrain.png|thumb|1219x1219px]]
#
#

Latest revision as of 23:02, 21 November 2021

Hydraulic Speed (Bergsbruk V2)

BergsbrukVehicleSpeed.png

When your inside a vehicle Press E to open the ECCS, Press the SPEED tab, Here you can edit all hydraulic speeds for that machine, it will not carry over to other machines.

WM1/WM2 is the 2 Work Modes you have on machines like the excavator when one controls the tracks and one the arm

The info "(Swing)" will not be accurate for most or any machines but have them so its not just numbers to remember what axis to adjust

Axis 1 & Axis 7 = W & S

Axis 2 & Axis 8 = A & D

Axis 3 & Axis 9 = L-Shift & L-Ctrl

Axis 4 & Axis 10 = Up Arrow & Down Arrow

Axis 5 & Axis 11 = Left Arrow & Right Arrow

Axis 6 & Axis 12 = R-Shift & R-Ctrl








Hydraulic Speed (Bergsbruk V3)

HydraulicSpeed.png

When your inside a vehicle Press I to open the ECCS, Press the SPEED tab, Here you can edit all hydraulic speeds for that machine, it will not carry over to other machines.

Primary/Secondary is the 2 Work Modes you have on machines like the excavator when one controls the tracks and one the arm

Axis 1 = W & S

Axis 2 = A & D

Axis 3 = L-Shift & L-Ctrl

Axis 4 = Up Arrow & Down Arrow

Axis 5 = Left Arrow & Right Arrow

Axis 6 = R-Shift & R-Ctrl

Steering Speed is for wheeled vehicles










Drivetrain Speed (Bergsbruk v2)

BergsbrukVehicleDrivetrain.png

When your inside a vehicle Press E to open the ECCS, Press the CTRL tab, and press DEV DRIVETRAIN Here you can edit all drivetrain speeds for that machine, it will not carry over to other machines.


Here you can edit how each gear behaves, Also set the Max RPM, Idle RPM, and the Max gear is the amount of gears the vehicle has, REMEMBER to save changes!

End Speed: The top speed the vehicle will have at that gear

Starts Speed: The minimum speed, dont touch this

Up Shift: The speed it will automaticly shift up, if its a automatic transmission

Down Shift: The speed it will automaticly shift down, if its a automatic transmission

High RPM: Highest RPM the engine will go to on that gear

Low RPM: Lowest RPM the engine will go to on that gear

Max Torque: The max amout of torque the engine has at the High RPM

Min Torque: The max amout of torque the engine has at theLow RPM