Difference between revisions of "How to modify vehicle speeds"

From Bergsbruk
Jump to navigation Jump to search
Line 3: Line 3:
[[File:BergsbrukVehicleSpeed.png|thumb|1229x1229px]]
[[File:BergsbrukVehicleSpeed.png|thumb|1229x1229px]]


When your inside a vehicle '''Press E''' to open the ECCS, Press the '''SPEED''' tab, Here you can edit all hydraulic speeds for that machine, it will not carry over to other machines.  
When your inside a vehicle '''Press I''' to open the ECCS, Press the '''SPEED''' tab, Here you can edit all hydraulic speeds for that machine, it will not carry over to other machines.  


'''WM1/WM2''' is the 2 Work Modes you have on machines like the excavator when one controls the tracks and one the arm  
'''WM1/WM2''' is the 2 Work Modes you have on machines like the excavator when one controls the tracks and one the arm  
Line 23: Line 23:


<br /><br /><br /><br /><br /><br /><br /><br /><br /><br />
<br /><br /><br /><br /><br /><br /><br /><br /><br /><br />
==Drivetrain Speed==
==(Only in Bergsbruk v2) Drivetrain Speed==
[[File:BergsbrukVehicleDrivetrain.png|thumb|1229x1229px]]
[[File:BergsbrukVehicleDrivetrain.png|thumb|1229x1229px]]
When your inside a vehicle '''Press E''' to open the ECCS, Press the '''CTRL''' tab, and press '''DEV DRIVETRAIN''' Here you can edit all drivetrain speeds for that machine, it will not carry over to other machines.  
When your inside a vehicle '''Press E''' to open the ECCS, Press the '''CTRL''' tab, and press '''DEV DRIVETRAIN''' Here you can edit all drivetrain speeds for that machine, it will not carry over to other machines.  

Revision as of 22:57, 21 November 2021

Hydraulic Speed

BergsbrukVehicleSpeed.png

When your inside a vehicle Press I to open the ECCS, Press the SPEED tab, Here you can edit all hydraulic speeds for that machine, it will not carry over to other machines.

WM1/WM2 is the 2 Work Modes you have on machines like the excavator when one controls the tracks and one the arm

The info "(Swing)" will not be accurate for most or any machines but have them so its not just numbers to remember what axis to adjust

Axis 1 & Axis 7 = W & S

Axis 2 & Axis 8 = A & D

Axis 3 & Axis 9 = L-Shift & L-Ctrl

Axis 4 & Axis 10 = Up Arrow & Down Arrow

Axis 5 & Axis 11 = Left Arrow & Right Arrow

Axis 6 & Axis 12 = R-Shift & R-Ctrl















(Only in Bergsbruk v2) Drivetrain Speed

BergsbrukVehicleDrivetrain.png

When your inside a vehicle Press E to open the ECCS, Press the CTRL tab, and press DEV DRIVETRAIN Here you can edit all drivetrain speeds for that machine, it will not carry over to other machines.


Here you can edit how each gear behaves, Also set the Max RPM, Idle RPM, and the Max gear is the amount of gears the vehicle has, REMEMBER to save changes!

End Speed: The top speed the vehicle will have at that gear

Starts Speed: The minimum speed, dont touch this

Up Shift: The speed it will automaticly shift up, if its a automatic transmission

Down Shift: The speed it will automaticly shift down, if its a automatic transmission

High RPM: Highest RPM the engine will go to on that gear

Low RPM: Lowest RPM the engine will go to on that gear

Max Torque: The max amout of torque the engine has at the High RPM

Min Torque: The max amout of torque the engine has at theLow RPM